-
When to Use This Checklist
-
Step 1: Write Down the Substrate and Application, One Page, Before You Ask for Quotes
-
Step 2: Confirm You're Talking to a Manufacturer, Not Just a Supplier
-
Step 3: Get the Test Methods in Writing — This Is the Step Most People Skip
-
Step 4: Sample Before You Negotiate Price
-
Step 5: Audit Compliance Documents at the Certificate Level, Not the Claim Level
-
Step 6: Put Payment, Invoicing, and Incoterms in One Document
-
Step 7: Run a Small Pilot With Quantified Acceptance Criteria
-
Notes and Common Mistakes
When to Use This Checklist
This is for you if you're coordinating a protective coating purchase for fabric or ABS and you're not a chemist, not a sourcing specialist, and not sure where to start. Maybe you inherited the supplier relationship from someone who left. Maybe your current supplier's quality has drifted and you need alternatives. Either way, this is the list I wish I'd had in 2020 when I took over purchasing.
The list assumes you're buying coatings at industrial volume (not consumer cans), sourcing from at least two or three potential suppliers, and that your product goes into a finished good someone else will inspect. If you're buying a custom formulation from scratch, this isn't the right checklist — you need a formulation consultant, not a supplier comparison.
There are seven steps. The one most people skip is Step 3 (test methods in writing). That one alone has saved me more rework than the other six combined.
Step 1: Write Down the Substrate and Application, One Page, Before You Ask for Quotes
Before a supplier quotes anything, they need to know exactly what the coating is going onto and what it needs to survive. If you skip this, you'll get quotes for the wrong product, and the comparison will be meaningless.
Here's what goes in the one-pager:
- Substrate spec. For fabric: fiber type (nylon 6/6, polyester, blends), weight (GSM), weave or knit construction. For ABS: grade (e.g., general-purpose, flame-retardant, plating-grade), whether parts are molded or thermoformed, and surface prep (bare vs. primed).
- Performance you actually need to hit. Adhesion class, flexibility, chemical resistance (which chemicals?), UV resistance, water resistance, abrasion cycles. Quantify where you can.
- Application method and cure conditions. Spray, dip, roll, or knife-over-roll. Cure temperature and time. If your line runs at 140°C for 90 seconds, say so — the coating has to be formulated for that window, not for 180°C.
- Service conditions. Indoor, outdoor, salt spray exposure, what it touches, how long it needs to last.
Two sentences is not a spec. A supplier will fill in the gaps with their most generic product, and that generic product is usually what fails first in the field.
Step 2: Confirm You're Talking to a Manufacturer, Not Just a Supplier
A lot of companies that market themselves as a protective coating manufacturer are trading companies. That's not automatically bad — traders can be responsive and can carry stock — but you need to know which one you're buying from, because when quality drifts you want a plant to call, not a WeChat account.
Three questions to send in writing:
- What is the physical address of the plant where this product is manufactured?
- Can you provide the business license or equivalent registration for the manufacturing entity?
- Was this formulation made at that plant, or sourced and relabeled?
Cross-check the plant address on a map service. If the "plant" is a residential building or a shared office park, ask again. If the answers come back vague, that's a signal — not a disqualifier, but a signal.
I'm not a chemical auditor, so I can't review their process controls. What I can do is ask for the plant address, the registration number, and a recent third-party factory audit report. If the order is going to be material, I'll budget $400–800 for a basic third-party audit. That's cheaper than a rejected production run.
Step 3: Get the Test Methods in Writing — This Is the Step Most People Skip
"Water-resistant," "high adhesion," and "chemical-resistant" are adjectives. They are not specifications. Before a supplier makes your shortlist, they need to tell you the exact method they tested against and give you a number.
For fabric coatings, the usual ones are:
- Hydrostatic pressure resistance — AATCC 127
- Spray rating — AATCC 22
- Durability after home laundering — AATCC 135
For ABS coatings, the usual ones are:
- Adhesion — ASTM D3359, Method B (5B is best, 0B is worst)
- Flexibility — ASTM D522, Method B
- Pencil hardness — ASTM D3363
- Impact resistance — ASTM D2794
- Salt spray — ASTM B117, if the part will see outdoor or coastal service
If a supplier can't put a method number on an email within a day, they don't have a test report — they have a marketing claim. Move on.
We once had a supplier confirm "same adhesion as our current supplier." When we asked which method, they told us they'd scratched with a fingernail. That's not ASTM D3359. We found out during a pilot run when the coating lifted at the seam after a folding test. Now I send the method list in the same email as the RFQ. No exceptions.
Step 4: Sample Before You Negotiate Price
Never negotiate a unit price before you've seen a sample. The cheapest quote is meaningless if the coating doesn't bond to your substrate.
Ask for three things with the sample:
- Confirm in writing that the sample is from a production batch, not a lab blend. Lab samples can be honest, but if you're going to pilot, pilot with production.
- Two sample bottles from what should be the same batch — a cheap way to check consistency without a full lab analysis.
- The batch number so you can cross-check it against the Certificate of Analysis later.
If your company has an application lab, run your own adhesion and flexibility check. If not, do a simple fold test and a peel check with tape, and photograph the result. It's not ASTM-grade data, but it catches gross mismatches before you commit to a pilot.
Step 5: Audit Compliance Documents at the Certificate Level, Not the Claim Level
"We are REACH compliant" and "we have an SVHC declaration dated last quarter" are not the same statement. Ask for the actual document, with a certificate or report number, and read it.
For fabric:
- REACH SVHC declaration (EU) with the current candidate list date
- OEKO-TEX or equivalent, if the fabric contacts skin
- CPSIA statement if the finished good sells in the US
For ABS:
- RoHS declaration (EU) with the directive reference
- REACH SVHC declaration
- SDS (safety data sheet) for handling and transport
According to the European Chemicals Agency (ECHA, echa.europa.eu), REACH requires suppliers to provide SVHC information when a substance in an article exceeds 0.1% w/w. If a supplier tells you the declaration isn't necessary because "the coating is applied and cured," follow up — cured coatings can still contain residuals above that threshold. Verify current requirements at the official source before signing anything.
Regulatory information here is general guidance only. Consult your compliance or legal team for current requirements in your specific market.
Step 6: Put Payment, Invoicing, and Incoterms in One Document
Invoicing is where small purchases go to die. I learned this the hard way — I once accepted a handwritten receipt for a $1,200 coating order from a new supplier. Finance rejected the expense. I spent three weeks chasing a proper invoice, and in the end the cost came out of my department budget. Now I verify invoicing capability before placing any order, no matter how small.
The one-pager should include:
- Pro forma invoice with buyer's full legal name and tax ID
- Payment terms: 30% T/T deposit on order, 70% against copy of B/L — or net 30 if you have prior history
- Beneficiary name matching the seller's legal entity (not a third party)
- Incoterms: EXW, FOB, or CIF, written into the contract, not just agreed verbally
- Currency and who bears FX movement
If the beneficiary on the pro forma doesn't match the name on the business license, stop and ask why.
Step 7: Run a Small Pilot With Quantified Acceptance Criteria
Don't jump from sample to bulk. Run a pilot of 5–10% of your expected order volume — or 100kg, whichever is smaller — and test it against the exact methods you agreed on in Step 3.
Checkpoints for the pilot:
- Test the pilot batch against the same method numbers you agreed in Step 3. If they tested against ASTM D3359, you test against ASTM D3359.
- Compare pilot vs. sample for color, viscosity, and cure behavior. A production batch that behaves differently from the sample is a red flag for process control.
- Match the CoA batch number to the physical drum label.
- If the volume is material, request a video walkthrough of the production line, or send one of your quality people on-site.
During our 2024 vendor consolidation, the spreadsheet said Vendor B was 14% cheaper per liter. My gut said their slow email replies would become slow deliveries. We pulled their on-time delivery data — it was under 80%. We went with Vendor A, slightly higher price, zero missed deliveries in three years. The spreadsheet was right about price. It was silent on risk.
Notes and Common Mistakes
Time pressure breaks every checklist, including this one. I once had a line down and two days to lock in a supplier. Normally I'd collect three quotes and run my own samples. Instead I went with prior history and trust. It worked out because the recommendation came from seven years of delivery records. But I don't recommend it. Keep a second source qualified at all times, even if you never use them.
Beware the vocabulary trap. I said "as soon as possible" on a delivery date and the supplier heard "no rush." Their ASAP was next Monday; mine was that afternoon. Now I write specific dates: "shipment ready by June 15, delivered by June 22." No ASAs. No "soon".
Compare total cost, not unit price. The cheapest quote often stops being cheapest once you add shipping, testing, rework, and the risk of a production stop. A unit price that's 10% higher but comes with a clean CoA, on-time delivery history, and prompt technical response is usually the lower total cost.
I'm not a coatings chemist, so I can't evaluate formulation chemistry — that needs your R&D or a technical consultant. What I can do, from a procurement seat, is make sure the supplier's claims are testable, their documents are checkable, and their invoices are payable. That's what this checklist covers. The chemistry is above my pay grade.
Every issue in this list — the scratched-nail "test," the handwritten receipt, the slow-email supplier — has cost me money or time at some point. Roughly $3,400 in rework and a two-week line stop, if I had to put a number on it. The checklist takes about half a day to build and it's saved me from more of those than I can count.
Prices mentioned are for general reference only and vary by region, specification, and date of quote. Verify current pricing with each supplier before placing an order.